EN 13164:2012+A1:2015工厂制聚苯乙烯泡沫(XPS)产品CE认证详解-上海郜盟

工厂制聚苯乙烯泡沫(XPS)产品ce认证标准

EN 13164:2012+A1:2015

Thermal insulation products for buildings - Factory made extruded polystyrene foam (XPS) products - Specification

建筑用隔热产品-工厂制聚苯乙烯泡沫(XPS)产品-规格

This European Standard specifies the requirements for factory made products of extruded polystyrene foam, with or without facings or coatings, which are used for thermal insulation of buildings. The products are manufactured in the form of boards which are also avallable with special edge and surface treatment (tongue & grooves, shiplap etc.).

本欧洲标准规定了用于建筑保温的厂制挤塑聚苯乙烯泡沫制品(无论是否带有饰面或涂层)的各项要求。这些制品以板状形式生产，且还可具备特殊的边角及表面处理工艺(如舌槽式、船板式等)。

Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered.

本标准涵盖的产品也用于预制保温系统和复合板;但不包括包含这些产品的系统的性能。

This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.

本标准描述了产品的特性，并包括测试程序、符合性评估、标识与标签。

The standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.

该标准并未明确说明产品需达到某一特定属性所要求的水平，以证明其在特定应用场合中的适用性。特定应用场合所需达到的水平应从相关法规或无冲突的标准中查找。

Products with a declared thermal resistance lower than 0,25 m2 KW or a declared thermal conductivity greater than 0,060 W/(m-K) at 10 °C are not covered by this standard.

声明热阻低于0.25m2·K/W或在10°C时热导率大于0.060W/(m·K)的产品不在本标准覆盖范围内。

This standard does not cover in situ insulation products, nor products intended to be used for the insulation of building equipment and industrial installations (covered by EN 14307), or civil engineering applications( covered by EN 14934).

本标准不涵盖现场绝缘产品，也不涉及旨在用于建筑设备与工业装置绝缘(由EN14307规范涵盖)或土木工程应用(由EN14934规范涵盖)的产品。

工厂制聚苯乙烯泡沫(XPS)产品ce认证法规

工厂制聚苯乙烯泡沫(XPS)产品产品出口欧盟需要满足CPR建材法规要求：

Regulation (EU) No 305/2011, Directive 89/106/EEC (CPD)【旧版】

工厂制聚苯乙烯泡沫(XPS)产品ce认证模式

有且仅有1个认证：模式 1，由欧盟公告机构进行测试和工厂审核后发证

制造商职责：	Factory production control (FPC)工厂生产控制;
	Further testing of samples taken at the factory工厂取样的进一步检验
Notified Body 公告机构职责：	Initial inspection of factory and FPC 工厂和FPC的初始检查;
	Continuous surveillance, assessment and approval of F.P.C. 持续监视、评估和批准F.P.C.