EN 14304:2009+A1:2013 工厂制柔性弹性泡沫材料(FEF)产品CE认证详解-上海郜盟

工厂制柔性弹性泡沫材料(FEF)产品ce认证标准

EN 14304:2009+A1:2013

Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products - Specification

建筑设备和工业装置用隔热产品.工厂制柔性弹性泡沫材料(FEF)产品.规范

This European Standard specifies the requirements for factory made flexible elastomeric foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 200 °C to + 175 °C.

本欧洲标准规定了用于建筑设备与工业装置热绝缘的厂制柔性弹性泡沫制品的各项要求，这些装置的工作温度范围约为一200°C至+175°C。

NOTE Below an operating temperature of - 50 °C, tests regarding the suitability of the products in the intended application shall be performed. Manufacturer's advice should be heeded in all cases.

注:在-50°C以下的运行温度下，应进行有关产品在预期应用中适用性的测试。所有情况下均应遵循制造商建议。

The products are manufactured in the form of sheets, tubes, rolls and tapes with or without coating and/or self-adhesive backing and/or different closure systems.

产品以片材、管状、卷材和带或不带涂层及/或自粘背衬和/或不同闭合系统的形式制造。

This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.

本欧洲标准描述了产品的特性，并包括测试、符合性评估、标识和标签的程序。

Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.

本标准涵盖的产品也用于预制保温系统和复合板;但不包括包含这些产品的系统的性能。

This European Standard does not specify the required level of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.

本欧洲标准并未具体规定某一特定属性所应达到的所需水平，该产品需通过满足这一水平来证明其在特定应用场合中的适用性。特定应用场合所需的各项标准可在相关法规及招标邀请文件中找到。

Products with a declared thermal conductivity greater than 0,050 W/(mK) at 10°C are not covered by this standard.

在10°C下，若产品声明的热导率大于0,050W/(m·K)，则不适用于本标准。

This European Standard does not cover products for the insulation of the building structure.

本欧洲标准不涵盖用于建筑结构保温的产品。

The normative part of this standard does not cover compressive stress (see Annex D, D.5).本标准的规范性部分不涵盖压缩应力(参见附录D，D.5)

工厂制柔性弹性泡沫材料(FEF)产品ce认证法规

工厂制柔性弹性泡沫材料(FEF)产品产品出口欧盟需要满足CPR建材法规要求：

Regulation (EU) No 305/2011, Directive 89/106/EEC (CPD)【旧版】

工厂制柔性弹性泡沫材料(FEF)产品ce认证模式

有且仅有1个认证：模式 1，由欧盟公告机构进行测试和工厂审核后发证

制造商职责：	Factory production control (FPC)工厂生产控制;
	Further testing of samples taken at the factory工厂取样的进一步检验
Notified Body 公告机构职责：	Initial inspection of factory and FPC 工厂和FPC的初始检查;
	Continuous surveillance, assessment and approval of F.P.C. 持续监视、评估和批准F.P.C.