EN 14308:2009+A1:2013硬质聚氨酯泡沫及聚异氰脲酸酯产品CE认证详解-上海郜盟

硬质聚氨酯泡沫及聚异氰脲酸酯产品ce认证标准

EN 14308:2009+A1:2013

Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products - Specification

建筑设备和工业装置的隔热保温产品.硬质聚氨酯泡沫及聚异氰脲酸酯产品.规范

This European Standard specifies the requirements for factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products, with a closed cell content not less than 90%, with or without facings, which are used for the thermal insulation of building equipment and industrial installations, with an operating temperature range of approximately, 200 °C to + 200 °C.

本欧洲标准规定了工厂生产的硬质聚氨酯泡沫(PUR)和聚异氰脲酸酯泡沫(PIR)产品的相关要求，其闭孔含量不得低于90%，无论是否带有饰面层，这些产品均用于建筑设备与工业设施的保温隔热，其工作温度范围约为-200°C至+200°C。

Below an operating temperature of - 50 °C, special tests regarding the suitability of the products in the intended application are advised (e.g liquefaction of oxygen). Manufacturer's advice should be heeded in all cases.

在低于-50°C的操作温度下，建议针对产品在预定应用中的适用性进行专门测试(例如氧气液化)。在任何情况下都应重视制造商提供的建议。

The products are manufactured in the form of blocks, faced or unfaced boards, pipe sections, segments and prefabricated ware.

产品以块状、带面或无面板、管段、段落和预制件的形式制造。

This European Standard describes product characteristics and includes procedures for testing,evaluation of conformity, marking and labelling.

本欧洲标准描述了产品的特性，并包括测试、符合性评估、标识和标签的程序。

Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered.

本标准涵盖的产品也用于预制保温系统和复合板;但不包括包含这些产品的系统的性能。This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations and invitations to tender.

本欧洲标准并未具体规定某一特定属性所应达到的所需水平，该产品需通过满足这些水平来证明其在特定应用场合中的适用性。特定应用场合所需的各项标准内容则需查阅相关法规及招标邀请文件。

Products with a declared thermal conductivity greater than 0,100 W/(m-K) at 10 °C are not covered by this European Standard.

在10°C下，若产品声明的热导率大于0.100W/(m·K)，则不适用于本欧洲标准。

This European Standard does not cover products for in situ-insulation (spraying or dispensing) or products for the insulation of the building structure.

本欧洲标准不适用于现场喷涂或灌注的保温产品，也不适用于建筑结构的保温材料。

This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.

本欧洲标准不涵盖以下声学方面:直接空气传播声学隔绝和冲击噪声传输指数。

硬质聚氨酯泡沫及聚异氰脲酸酯产品ce认证法规

硬质聚氨酯泡沫及聚异氰脲酸酯产品产品出口欧盟需要满足CPR建材法规要求：

Regulation (EU) No 305/2011, Directive 89/106/EEC (CPD)【旧版】

硬质聚氨酯泡沫及聚异氰脲酸酯产品ce认证模式

有且仅有1个认证：模式 1，由欧盟公告机构进行测试和工厂审核后发证

制造商职责：	Factory production control (FPC)工厂生产控制;
	Further testing of samples taken at the factory工厂取样的进一步检验
Notified Body 公告机构职责：	Initial inspection of factory and FPC 工厂和FPC的初始检查;
	Continuous surveillance, assessment and approval of F.P.C. 持续监视、评估和批准F.P.C.