EN 14309:2009+A1:2013 工厂生产膨胀聚苯乙烯(EPS)产品CE认证详解-上海郜盟

工厂生产膨胀聚苯乙烯(EPS)产品ce认证标准

EN 14309:2009+A1:2013

Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification

建筑设备和工业装置的隔热保温产品.工厂生产膨胀聚苯乙烯(EPS)产品.规格

This European Standard specifies the requirements for factory made products of expanded polystyrene which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 180 °C to + 80 °C. Modified expanded polystyrene polymers with a higher temperature resistance are also covered by this standard.

本欧洲标准规定了用于建筑设备与工业装置热绝缘的聚苯乙烯发泡制品的厂制产品所应满足的各项要求。这些制品的使用温度范围约为-180°C至+80°C。本标准还涵盖了具有更高耐热性能的改性聚苯乙烯发泡聚合物。

Below an operating temperature of 50 °C, special tests regarding the suitability of the product in the intended application are advised (e.g liquefaction of oxygen). Manufacturers' advice should be heeded in all cases.

在低于-50°C的操作温度下，建议针对产品在预定应用中的适用性进行专门测试(例如氧气液化)。在任何情况下都应重视制造商提供的建议。

The products are manufactured in the form of faced or unfaced boards, rolls, lags, pipe sections or other prefabricated ware.

产品以带面或无面板、卷材、膨胀管、管道段或其他预制件的形式制造。

This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.

本标准描述了产品的特性，并包括测试、符合性评估、标识和标签的程序。

Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.

本标准涵盖的产品也用于预制保温系统和复合板中;但不包括包含这些产品的系统的性能要求

This standard does not specify the required level or class of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application can be found in regulations and invitations to tender.

本标准并未具体规定某一特定属性应达到的所需级别或类别，该产品需通过满足这些要求来证明其在特定应用场合中的适用性。特定应用所需的类别和级别可在相关法规及招标邀请文件中找到。

Products with a declared thermal conductivity greater than 0,060 W/(m-K) at 10 °C are not covered by this standard.

在10°C下，若产品声明的热导率大于0.060W/(m·K)，则不适用于本标准。

This standard does not cover products for in situ insulation (for loose fill or poured insulation) or products for the insulation of the building structure.

本标准不适用于现场保温产品(用于松散填充或浇注式保温)或建筑结构的保温产品

工厂生产膨胀聚苯乙烯(EPS)产品ce认证法规

工厂生产膨胀聚苯乙烯(EPS)产品产品出口欧盟需要满足CPR建材法规要求：

Regulation (EU) No 305/2011, Directive 89/106/EEC (CPD)【旧版】

工厂生产膨胀聚苯乙烯(EPS)产品ce认证模式

有且仅有1个认证：模式 1，由欧盟公告机构进行测试和工厂审核后发证

制造商职责：	Factory production control (FPC)工厂生产控制;
	Further testing of samples taken at the factory工厂取样的进一步检验
Notified Body 公告机构职责：	Initial inspection of factory and FPC 工厂和FPC的初始检查;
	Continuous surveillance, assessment and approval of F.P.C. 持续监视、评估和批准F.P.C.