EN 14313:2009+A1:2013 工厂制聚乙烯泡沫(PEF)产品CE认证详解-上海郜盟

工厂制聚乙烯泡沫(PEF)产品ce认证标准

EN 14313:2009+A1:2013

Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products - Specification

建筑设备和工业装置用隔热产品.工厂制聚乙烯泡沫(PEF)产品.规范

This European Standard specifies the requirements for factory made flexible polyethylene foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately-80°C to+150°C.

本欧洲标准规定了用于建筑设备与工业装置热绝缘的厂制软质聚乙烯泡沫制品的各项要求，这些制品的工作温度范围约为一80°C至+150°C。

Tensile stress in the insulation product should be avoided when applying PEF.This is even more important when applying PEF on lines with operating temperatures between -50°C and -80°°C.The tensile stress should be kept at the minimum by applying the foam"under pressure",i.e.cutting the parts in a generous way.Manufacturer's advice should be heeded in all cases.

在应用PEF时，应尽量避免绝缘制品中的拉伸应力。尤其是在应用于运行温度介于-50°C至-80°C之间的线路时，这一点显得尤为重要。应通过“加压”方式(即以大角度切割部件)来将拉伸应力保持在最低限度。在任何情况下都应谨遵制造商的建议行事。

The products are manufactured in the form of tubes.profiles,sheets,rolls and tapes with or without coating and/or self-adhesive backing and/or different closure systems.

产品以管状、型材、板材、卷材和带或不带涂层的胶粘背衬及/或不同闭合系统的形式制造。

This standard describes product characteristics and includes procedures for testing,evaluation of conformity,marking and labelling.

本标准描述了产品的特性，并包括测试、符合性评估、标识和标签的程序。

Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels;the performance of systems incorporating these products is not covered.

本标准涵盖的产品也用于预制保温系统和复合板;但不包括包含这些产品的系统的性能。

This standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application.The levels required for a given application can be found in regulations and invitations to tender.

本标准并未明确指定某一特定属性所应达到的必备水平，该水平是产品用以证明在特定应用场合中适用性的必要条件。特定应用场合所需的各项标准可在相关法规及招标邀请文件中找到。

Products with a declared thermal conductivity greater than 0,050 W/(m-K)at 10°°C are not covered by this standard.

在10°C下，若产品声明的热导率大于0,050W/(m·K)，则不适用于本标准。

This standard does not cover products for the insulation of the building structure.

本标准不适用于建筑结构的保温产品。

The normative part of this standard does not cover compressive stress (see C.4).

本标准的规范性部分不涵盖压缩应力(参见C.4)

工厂制聚乙烯泡沫(PEF)产品ce认证法规

工厂制聚乙烯泡沫(PEF)产品产品出口欧盟需要满足CPR建材法规要求：

Regulation (EU) No 305/2011, Directive 89/106/EEC (CPD)【旧版】

工厂制聚乙烯泡沫(PEF)产品ce认证模式

有且仅有1个认证：模式 1，由欧盟公告机构进行测试和工厂审核后发证

制造商职责：	Factory production control (FPC)工厂生产控制;
	Further testing of samples taken at the factory工厂取样的进一步检验
Notified Body 公告机构职责：	Initial inspection of factory and FPC 工厂和FPC的初始检查;
	Continuous surveillance, assessment and approval of F.P.C. 持续监视、评估和批准F.P.C.