EN1433排水沟/排水通道/格栅CE认证测试全标准解读
EN 1433:2002
EN 1433:2002/A1:2005
Drainage channels for vehicular and pedestrian areas — Classification, design and testing requirements, marking and evaluation of conformity
车辆和行人区域的排水通道-分类、设计和试验要求、标记和符合性评价
1 Scope范围
This European Standard specifies requirements for linear drainage channels for the collection and conveyance of surface water when installed within areas subjected to pedestrian and/or vehicular traffic.
本欧洲标准规定了在行人和/或车辆通行区域内安装用于收集和输送地表水的线性排水通道的要求。
These channels are defined as either Type I, which requires no further support or Type M, which requires additional support to accommodate the vertical and horizontal loads in service, in accordance with the manufacturers' recommendations.
根据制造商的建议,这些通道被定义为I型(不需要进一步的支撑)或M型(需要额外的支撑以适应服务中的垂直和水平载荷)。
This standard specifies requirements for gratings and covers integral with a linear drainage system. This standard applies to grid units, slot units and kerb units up to a clear opening of 1 000 mm.
本标准规定了格栅的要求,并涵盖了线性排水系统的整体。本标准适用于网格单元、槽单元和路沿单元,通孔不超过1000mm。
This standard specifies definitions, classes, design and testing requirements, marking and quality control for drainage channels.11
本标准规定了排水渠道的定义、等级、设计和测试要求、标记和质量控制
2 产品款型
type I I型
drainage channel which requires no further support to accommodate the vertical and horizontal loads in service不需要进一步支撑以容纳竖向和水平荷载的排水渠道
type M M型
drainage channel which requires additional support to accommodate the vertical and horizontal loads in service需要额外支撑的排水通道,以适应使用中的垂直和水平荷载
带格栅的排水通道
格栅的常见款式
slot unit
prefabricated drainage channel unit having closed profile and a continuous or intermittent inlet slot on top to permit the intake of surface water:预制的排水通道单元,具有封闭的剖面和一个连续的或间歇的入口槽,在顶部允许地表水的入口
kerb unit
drainage channel with a kerb type profile and having continuous or intermittent drainage openings具有路边型轮廓并具有连续或间歇排水开口的排水通道
3 分类
A 15, B 1 25, C 250, D 400, E 600, F 900.
Group 1 (min. class A 15) Areas which can only be used by pedestrians and pedal cyclists. 只允许行人和骑自行车者使用的区域。 |
Group 2 (min. class B 125) Footways, pedestrian areas and comparable areas, private car parks or car parking decks. EN 1433:2002 (E) 行人道、行人区及类似地方、私家停车场或停车场平台。EN 1433:2002 (E) |
Group 3 (min. class C 250) Kerb sides (Figure 1 0) and non-trafficked areas of hard shoulders and similar; Kerb units are always group 3. 路边(图10)和非通行区域的硬肩和类似;路肩单位是第3组。 |
Group 4 (min. class D 400) Carriageways of roads (including pedestrian streets), hard shoulders (Figures 10 and 11) and parking areas, for all types of road vehicles. 适用于各类道路车辆的行车道(包括行人街道)、硬路肩(图10及11)及停车场。 |
Group 5 (min. class E 600) Areas subjected to high wheel loads, e. g. ports and dock sides. 受高轮载影响的地区,如港口和码头边。 |
Group 6 (class F 900) Areas subjected to especially high wheel loads e. g. aircraft pavements. 到特别高车轮载荷的地区,例如飞机路面 |
4材料
1)排水通道常见材料
a) flake graphite cast iron; 片状石墨铸铁
b) spheroidal graphite cast iron; 球墨铸铁
c) cast steel; 铸钢
d) rolled steel; 轧钢
e) stainless steel; 不锈钢
f) reinforced or unreinforced concrete; 钢筋或非钢筋混凝土
g) synthetic resin concrete; 合成树脂混凝土
h) concrete with fibre; 钢纤维混凝土
i) one of the materials a) to f) combined with concrete/synthetic resin concrete with fibre. a)到f)与混凝土/合成树脂混凝土与纤维结合的一种材料
2)格栅及盖板常见材料:
a) flake graphite cast iron; 片状石墨铸铁
b) spheroidal graphite cast iron; 球墨铸铁
c) cast steel; 铸钢
d) rolled steel; 轧钢
e) stainless steel; 不锈钢
f) copper based alloys; 铜基合金
g) reinforced concrete; 钢筋混凝土
h) synthetic resin concrete. 合成树脂混凝土
5 测试项目及标准
1)Water-tightness水密性
- jointing of drainage channels排水渠接缝
. When tested in accordance with 9.3.6, the joint and the bodies shall not show leakage.
当按照9.3.6进行测试时,接头和阀体应不显示泄漏。
2)Load bearing capacity, deflection under load承载能力,荷载下挠度
- maximum load最大负载
- Permanent set永久定型
其中不同等级登对的测试负载:
6 CE认证系统/模式
系统/模式3:由有EN1433 CPR认证资质的NB公告号机构进行测试
7 CE标识样板
8了解更多
上海郜盟,拥有欧盟多家公告号机构CE认证授权,可提供权威专业的CE认证测试认证技术服务,认证周期短,服务高效。详情咨询021-34122669