上海郜盟为您专业解读集装箱/托盘运输车CE认证：

1、集装箱/托盘运输车欧盟CE认证指令

MD机械指令：2006/42/EC

2、集装箱/托盘运输车欧盟CE认证标准：

EN ISO 12100：2010 机械安全 - 用于设计的一般准则-风险评估及风险降低

EN 60204-1：2018 机械安全.机械电气设备.第1部分：一般要求

EN 12312-10:2005+A1:2009 Aircraft ground support equipment - Specific requirements - Part 10: Container/Pallet transfer transporters飞机地面支持设备.特殊要求.第10部分：集装箱/托盘运输车

3、EN 12312-10:2005+A1:2009适用范围：

This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of container/pallet transfer transporters when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some performance requirements recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies. This European Standard applies to self-propelled container/pallet transfer transporters, with a seated driver. Examples of typical transfer transporters are shown in Annex A. This European Standard does not apply to: loading equipment with a height adjustment capability in excess of 150 mm; transporter-loaders (single platform loader with transporter capability, see EN 12312-9); roller-bed transport platforms mounted on unmodified commercial road chassis. This European Standard does not establish requirements for noise and vibration. Noise and vibration are dealt with respectively in EN 1915-4 and EN 1915-3. This European Standard is not dealing with hazards in respect to a standard automotive chassis and the traffic on the apron. This Part of EN 12312 is not applicable to GSE which are manufactured before the date of publication by CEN of this European Standard. NOTE Certain measurements have been given in imperial units (in parentheses) following the metric measurements since the containers/pallets to be handled are based mainly on the imperial system. This part of EN 12312 is intended to be used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 (for vehicles) and EN 1915-4.上海郜盟提醒您，本欧洲标准规定了在按照制造商或其授权代表给出的规范进行集装箱/托盘转运运输车的调试、操作和维护过程中，将第4条所列危险降至最低的技术要求。它还考虑了当局、飞机和地面支持设备（GSE）制造商以及航空公司和处理机构认为至关重要的一些性能要求。本欧洲标准适用于带座椅驾驶员的自推进式集装箱/托盘运输车。附件A中显示了典型的转运运输车示例。本欧洲标准不适用于：高度调节能力超过150 mm的装载设备；运输装载机（具有运输能力的单平台装载机，见EN 12312-9）；安装在未经修改的商业道路底盘上的辊道式运输平台。本欧洲标准未规定噪声和振动要求。噪声和振动分别在EN 1915-4和EN 1915-3中进行了处理。本欧洲标准不涉及标准汽车底盘和停机坪交通的危险。EN 12312的本部分不适用于在CEN发布本欧洲标准之前制造的GSE。注：由于待处理的集装箱/托盘主要基于英制，因此公制计量后的某些计量单位为英制单位（括号内）。EN 12312的本部分旨在与EN 1915-1、EN 1915-2、EN 1915-3（车辆）和EN 1915-4结合使用。

5、集装箱/托盘运输车CE认证流程

1 提交CE申请

2 准备测试样机和技术资料

3 样机测试与整改

4 技术资料审核与整改，上海郜盟专业指导

5 公告机构审核通过后，工厂获得CE证书

6 设备加贴CE标识，顺利在欧盟市场流通

上海郜盟-欧盟公告机构授权-专业CE认证

了解更多：

机械设备CE认证

CE认证是什么认证？

欧盟CE认证

上海郜盟，专业CE认证技术服务公司，致力于中国制造全球化服务！提供权威CE认证机构-欧盟公告号机构机械设备CE认证服务，高效可靠！

未经允许不得转载！

详情咨询021-34122669，021-34120602