上海郜盟专业CE认证为您解读

1、平板玻璃制造配套运输设备欧盟CE认证指令

MD机械指令：2006/42/EC

2、平板玻璃制造配套运输设备欧盟CE认证标准：

EN ISO 12100：2010 机械安全 - 用于设计的一般准则-风险评估及风险降低

EN 60204-1：2018 机械安全.机械电气设备.第1部分：一般要求

EN 13035-1:2008 Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory平板玻璃制造、处理和加工用机器和设备.安全要求.第1部分：工厂内的储存、搬运和运输设备

3、EN 13035-1:2008适用范围：

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage, handling and transportation of flat glass inside the factory as described in Clause 3. It applies to stationary, movable and mobile storage equipment (see 3.2), mechanical and pneumatic handling equipment (see 3.3) and transportation equipment (see 3.4) (see overview in Annex A).

1.2 Additional requirements for dealing with specific hazards due to the use outside the factory are dealt with in prEN 13035-2.

1.3 This standard only deals with the devices which are directly in contact with the glass. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass (see 3.4.1). This standard does not apply to manual handling equipment as defined in 3.3.1.

1.4 These standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard.

1.5 This document is not applicable to storage, handling or transportation equipment for flat glass inside the factory, which is manufactured before the date of its publication as EN.

1.1本标准包含第3条所述工厂内平板玻璃储存、搬运和运输设备设计和安装的安全要求。它适用于固定、移动和移动存储设备（见3.2）、机械和气动搬运设备（见3.3）和运输设备（见3.4）（见附录A中的概述）。

1.2 prEN 13035-2规定了处理因工厂外使用而产生的特定危险的附加要求。

1.3本标准仅涉及与玻璃直接接触的装置。拖拉机、起重机、起重机和叉车以及不与玻璃接触的其他机动车辆部件不在范围内（见3.4.1）。本标准不适用于3.3.1中定义的手动搬运设备。

1.4本标准涉及与平板玻璃储存、搬运和运输设备相关的所有重大危险、危险情况和事件，当其按预期使用时，以及在制造商合理预见的误用条件下使用（见第4条）。本标准规定了适当的技术措施，以消除或减少调试、运行和维护期间重大危险产生的风险。噪声未被认为是本标准范围内任何类型设备的重大危害。

1.5本文件不适用于工厂内平板玻璃的储存、搬运或运输设备，该设备在其发布为EN之前制造。