上海郜盟专业CE认证为您解读

1、起重机非固定负载提升附件欧盟CE认证指令

MD机械指令：2006/42/EC

2、起重机非固定负载提升附件欧盟CE认证标准：

EN ISO 12100：2010 机械安全 - 用于设计的一般准则-风险评估及风险降低

EN 60204-1：2018 机械安全.机械电气设备.第1部分：一般要求

EN 13155:2003+A2:2009 Cranes - Safety - Non-fixed load lifting attachments起重机.安全.非固定负载提升附件

3、EN 13155:2003+A2:2009 适用范围：

This European Standard specifies safety requirements for the following non-fixed load lifting attachments for cranes, hoists and manually controlled load manipulating devices: plate clamps; vacuum lifters; self priming, non-self priming (pump, venturi, turbine); electric lifting magnets (battery fed and mains-fed); permanent lifting magnets; electro-permanent lifting magnets; lifting beams; C-hooks; lifting forks; clamps; defined in clause 3.

This standard does not specify the additional requirements for: non fixed load lifting attachments in direct contact with foodstuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons; hazards resulting from handling specific hazardous materials (e.g. explosives, hot molten masses, radiating materials); hazards caused by operation in an explosive atmosphere; hazards caused by noise; electrical hazards; hazards due to hydraulic and pneumatic components. This standard does not cover the hazards related to mechanical strength of structural elements of attachments designed for more than 20 000 lifting cycles. NOTE The coefficient of utilization specified in clause 5.1.1 ensures that no fatigue verification is needed for less than 20 000 cycles. This is in accordance with the well accepted calculation codes e.g., FEM 1001. This standard does not cover attachments intended to lift above people. This standard does not cover slings, ladles, expanding mandrels, buckets, grabs, or grab buckets. The hazards covered by this European Standard are identified in clause 4. This European Standard does not cover hazards related to the lifting of persons. This European Standard is applicable to non-fixed load lifting attachments which are manufactured after the date of approval by CEN of this standard.

上海郜盟专业认证本欧洲标准规定了起重机、起重机和手动控制负载操纵装置的以下非固定负载提升附件的安全要求：板夹；真空提升器；自吸、非自吸（泵、文丘里管、涡轮机）；电动升降磁铁（电池供电和电源供电）；永久起重磁铁；电动永磁体；吊梁；C形钩；升降叉；夹具；定义见第3条。

本标准未规定以下方面的附加要求：与食品或药品直接接触的非固定负载提升附件，出于卫生原因需要高度清洁；处理特定危险材料（如爆炸物、热熔融物质、辐射材料）造成的危险；在爆炸性环境中作业造成的危险；噪声造成的危害；电气危险；液压和气动部件造成的危险。本标准不包括与设计用于20000次以上提升循环的附件的结构元件的机械强度相关的危险。注：第5.1.1条中规定的利用系数可确保不需要进行小于20000次循环的疲劳验证。这符合公认的计算代码，例如FEM 1001。本标准不包括用于提升人员上方的附件。本标准不包括吊索、钢包、膨胀心轴、铲斗、抓斗或抓斗。本欧洲标准涵盖的危险在第4条中进行了识别。本欧洲标准不包括与人员吊装相关的危险。本欧洲标准适用于CEN批准本标准后制造的非固定载荷起重附件。