上海郜盟专业CE认证为您解读

1、集装箱/托盘装载机欧盟CE认证指令

MD机械指令：2006/42/EC

2、集装箱/托盘装载机欧盟CE认证标准：

EN ISO 12100：2010 机械安全 - 用于设计的一般准则-风险评估及风险降低

EN 60204-1：2018 机械安全.机械电气设备.第1部分：一般要求

EN 12312-9:2013 Aircraft ground support equipment - Specific requirements - Part 9: Container/Pallet loaders飞机地面支持设备.特殊要求.第9部分：集装箱/托盘装载机

3、EN 12312-9:2013 适用范围：

This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, the operation and the maintenance of container/pallet loaders when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some requirements recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies. This document applies to:

a) Container/Pallet loader (self-propelled) single platform;

b) Container/Pallet loader (self-propelled) two or more platforms;

c) Container/Pallet loader/transporter (self-propelled);

d) Container/Pallet loader/transfer platform (towed).

This document does not establish requirements for noise and vibration. NOTE 1 EN 1915-3 and EN 1915-4 provide the general GSE noise and vibration requirements. This standard does not deal with hazards in respect to a standard automotive chassis and from other vehicles on the apron. This part of EN 12312 is not applicable to container/pallet loaders which are manufactured before the date of publication of this standard by CEN. NOTE 2 Certain measurements have been given in imperial units (in parentheses) following the metric measurements since the containers/pallets to be handled are based mainly on the imperial system. This part of EN 12312 when used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4 provides the requirements for container/pallet loaders.

本欧洲标准规定了将第4条中列出的危险降至最低的技术要求，这些危险在集装箱/托盘装载机按预期使用时的调试、操作和维护过程中可能出现，包括制造商合理预见的误用，当按照制造商或其授权代表给出的规范进行时。它还考虑了当局、飞机和地面支持设备（GSE）制造商以及航空公司和处理机构认为至关重要的一些要求。本文件适用于：

a）集装箱/托盘装载机（自行式）单平台；

b）集装箱/托盘装载机（自行式）两个或多个平台；

c）集装箱/托盘装载机/运输车（自行式）；

d）集装箱/托盘装载机/转运平台（牵引）。

本文件未规定噪声和振动要求。注1 EN 1915-3和EN 1915-4提供了通用GSE噪声和振动要求。本标准不涉及标准汽车底盘和停机坪上其他车辆的危险。EN 12312的本部分不适用于CEN发布本标准之前制造的集装箱/托盘装载机。注2：由于待处理的集装箱/托盘主要基于英制，因此公制计量后的某些计量单位为英制单位（括号内）。当与EN 1915-1、EN 1915-2、EN 1915-3和EN 1915-4一起使用时，EN 12312的本部分规定了集装箱/托盘装载机的要求。