EN 15095:2007 +A1:2008电动仓储货架CE认证详解

www.gaomengce.com

上海郜盟为您专业解读电动仓储货架机械CE认证标准： EN 15095:2007 +A1:2008 Power-operated mobile racking and shelving, carousels and storage lifts — Safety requirements电动移动式货架和托盘架、旋转式货架和仓储提升机 - 安全要求

常见电动仓储货架类别：

• 1垂直循环式存储设备（垂直回转货架）上海郜盟CE认证

• 2水平循环式存储设备（水平环形货柜）上海郜盟CE认证

• 3仓储升降机上海郜盟CE认证

• 4移动货架上海郜盟CE认证

• 5移动式托盘货架上海郜盟CE认证

 Safety requirements and protective measures电动货架安全要求和防护措施-上海郜盟CE认证

1 General requirements

Storage equipment shall conform to the safety requirements and/or protective measures of this section and also to the requirements of EN ISO 12100-1 and EN ISO 12100-2 concerning relevant but not significant hazards, which are not dealt with in this standard.

Storage equipment and their accessories shall be suitable for operation in the intended condition of use in the working environment for which they have been designed.

存储设备应符合本节的安全要求和/或防护措施，同时也要符合 EN ISO 12100-1 和 EN ISO 12100-2 中有关虽相关但不重要的危险的要求，这些危险在本标准中未作处理。存储设备及其附件应适合在其设计所针对的工作环境中预期使用条件下运行。

Care shall be taken to review the safety aspects of the interfaces with other storage products such as mobile and static racking or pedestrian access areas.

应仔细审查与其他存储产品（如移动式和固定式货架或行人通道）接口的安全方面。

2 Mechanical hazards

2.1 Design and Installation

2.1.1 General

Storage equipment shall be designed and installed in such a way that it is able to support the load of the storage goods safely when used in a correct manner.

存储设备的设计和安装应确保其在正确使用时能够安全地承受所存储货物的重量。

The stability and load carrying capacity shall be sufficient for the operating loads and be established through calculations of the carrying capacity of the load bearing elements or via static load tests.

稳定性和承载能力应足以承受运行载荷，并通过承载元件承载能力的计算或通过静载试验确定。

The intersection between single components shall be co-ordinated (e. g.: connecting forces, -moments and - stiffness's, as well as electrical, pneumatic and hydraulic connections).

各单个部件之间的连接点应加以协调（例如：连接力、力矩和刚度，以及电气、气动和液压连接）。

2.1.2 Installation安装

Storage equipment and their accessories shall be constructed so that they can be safely installed. If necessary anchorage points for safety harnesses shall be provided.

存储设备及其附件应设计成能够安全安装。如有必要，应提供安全带的固定点。

Storage equipment shall be aligned vertically to the tolerances specified by the designer and as laid down in the installation instructions.

存储设备应按照设计者规定的公差和安装说明的要求垂直对齐。

The maximum deviation from the vertical shall not exceed 1/350 of the height.

最大垂直偏差不得超过高度的 1/350。

2.1.3 Stability稳定性

The stability factor in the serviceability state (normal operation) with regard to tipping due to inertia forces or due to horizontal placement loads considered separately shall be at least 2.0: 在正常使用状态（正常运行）下，分别考虑由于惯性力或水平放置荷载引起的倾覆时的稳定性系数应至少为 2.0：

了解更多电动货架欧盟法规要求和CE认证要求，请联系上海郜盟专业认证工程师021-34122669,18018853504，info@cegaomeng.com

上海郜盟，致力于中国产品全球化服务，帮助中国工厂和外贸企业快速打破国际贸易壁垒！！！

原创文件，严禁转载！！！